It is extremely important to keep both the crystal and circuitry in a controlled structure so as to manage temperature sensitivity. This is what denotes a stable temperature, which ought to be higher than the one responsible for exposing OCXO 10MHz Frequency Reference. Better still; the oven can perform better if it is set to turnover resonators degree to give it the capability of balancing with the outside temperature.
If the temperature is controlled, then anomalies associated with temperature effects will be reduced to minimal. These temperature anomalies have effects on the resonators and may just allow compensation within a limited allowance. Higher overtone crystals may also be used in such controlled temperatures. This is better because they are stable in controlled conditions.
These oscillators know how to enable stability as compared to others like SPXO and TCXO which do not have any temperature control mechanisms. It is the crystal units that determine temperature characteristics. Oven controlled oscillator is far much better because the oven block enables it to maintain the temperature at a stable state.
Its stability is majorly resulting from both the static and dynamic characteristics. These could be on the resonator, the range of the design temperature and stability of other components such as the oven accuracy. Even though temperature stability works in a given range, narrow ranges give improved stability because lots of it is restricted and channelled to a specific section.
More power needs to be considered for the oven controlled oscillator because its consumption is enormous. Depending on the insulation kind, you will be able to determine the power needed for such operations. The higher it goes, the lesser heat used, which in turn helps in usage as minimal as possible.
The oven temperature ought to be set to some high level than the renowned ambient one to enable the oven to control everything better. This calls for warming of the resonator so as to get the required heat. All these are done so that the oven can be allowed to balance to equilibrium.
Proper regulation should also be carried out so that the voltage supply does not have any variations. If not checked, then disturbances may be noticed within oscillator frequency and this could hinder its performance. Difference in power if realized can cause delay and let the supply go back to equilibrium, leading to wastage of more time.
Since the oscillator is sensitive to load, an amplifier could be used so that multiple outputs can be obtained. This is the reason why they should be built around the oven so that temperature stability does not interfere so much. Humidity also needs to be checked because it could have some impact on the stability.
Such issues may be averted by measuring instability and modelling it to the required standards. Control mechanisms are also available and can be used for the better to avert instability. Temperature compensation can be achieved through such mechanisms. Additional characteristic like retrace is another option which can be applied for these aversion purposes.
If the temperature is controlled, then anomalies associated with temperature effects will be reduced to minimal. These temperature anomalies have effects on the resonators and may just allow compensation within a limited allowance. Higher overtone crystals may also be used in such controlled temperatures. This is better because they are stable in controlled conditions.
These oscillators know how to enable stability as compared to others like SPXO and TCXO which do not have any temperature control mechanisms. It is the crystal units that determine temperature characteristics. Oven controlled oscillator is far much better because the oven block enables it to maintain the temperature at a stable state.
Its stability is majorly resulting from both the static and dynamic characteristics. These could be on the resonator, the range of the design temperature and stability of other components such as the oven accuracy. Even though temperature stability works in a given range, narrow ranges give improved stability because lots of it is restricted and channelled to a specific section.
More power needs to be considered for the oven controlled oscillator because its consumption is enormous. Depending on the insulation kind, you will be able to determine the power needed for such operations. The higher it goes, the lesser heat used, which in turn helps in usage as minimal as possible.
The oven temperature ought to be set to some high level than the renowned ambient one to enable the oven to control everything better. This calls for warming of the resonator so as to get the required heat. All these are done so that the oven can be allowed to balance to equilibrium.
Proper regulation should also be carried out so that the voltage supply does not have any variations. If not checked, then disturbances may be noticed within oscillator frequency and this could hinder its performance. Difference in power if realized can cause delay and let the supply go back to equilibrium, leading to wastage of more time.
Since the oscillator is sensitive to load, an amplifier could be used so that multiple outputs can be obtained. This is the reason why they should be built around the oven so that temperature stability does not interfere so much. Humidity also needs to be checked because it could have some impact on the stability.
Such issues may be averted by measuring instability and modelling it to the required standards. Control mechanisms are also available and can be used for the better to avert instability. Temperature compensation can be achieved through such mechanisms. Additional characteristic like retrace is another option which can be applied for these aversion purposes.